MIP_NL__0P_aux_data_packet

binary record "MIP_NL__0P_aux_data_packet"size: 1400
idfield namedefinition
0mcmd_execution_field
binary uint16size: 2
Macrocommand Execution Field
1mpd_relay_contact_ods_status
binary uint16size: 2
MPD Relay Contact / ODS Status
2direct_voltage_current_status
binary uint16size: 2
Direct Voltage/Current Status
3idu_status
binary uint16size: 2
IDU Status. Least significant byte denotes forward/reverse sweeps; 0 = counterclockwise; 1 = clockwise sweep.
4idu_error_status
binary uint16size: 2
IDU Error Status
5heater_power_level_relay_status
binary uint16size: 2
Heater Power Level and Relay Status
6asu_cmd_status
binary uint16size: 2
ASU Command Status
7asu_direct_status
binary uint16size: 2
ASU Direct Status
8esu_cmd_status
binary uint16size: 2
ESU Command Status
9esu_direct_status
binary uint16size: 2
ESU Direct Status
10spe_config_status
binary uint32size: 4
SPE Configuration Status
11fca_status
binary array[6]size: 12
FCA Status
binary uint16size: 2
12sw_cmcd_status
binary uint16size: 2
SW Command Status
13dpu_detector_thermistor_1
binary uint16size: 2
Thermistor #1 temperature at the detectors (12 bits, range 0--337K)
14dpu_detector_thermistor_2
binary uint16size: 2
Thermistor #2 temperature at the detectors (12 bits, range 41--91K)
15latest_scan_gate_start_time
binary uint32size: 4
Latest Scan Gate Start Time

unit: "1/256 s"
16previous_scan_gate_start_time
binary uint16size: 2
Previous Scan Gate Start Time

unit: "1/256 s"
17end_identifier_1
binary uint16size: 2
Constant value (FFFF, hex).
18substeps_heater_mode
binary uint16size: 2
Substeps to Heater Mode
19aps_pos_last_scan_gate_start
binary uint32size: 4
APS Position at Last Scan Gate Start
20aps_pos_last_scan_gate_stop
binary uint32size: 4
APS Position at Last Scan Gate Stop
21measured_az_los
binary uint32 (double)size: 4
Measured Azimuth LOS

unit: "1e-5 degrees"

converted unit: "degrees" (multiply by 1/100000)
22measured_el_los
binary uint32 (double)size: 4
Measured Elevation LOS

unit: "1e-5 degrees"

converted unit: "degrees" (multiply by 1/100000)
23low_level_currents
binary array[5]size: 10
Low Level Currents
binary uint16size: 2
24ice_box_a_temp_radiator
binary uint16size: 2
ICE box A temp (radiator)
25ice_box_b_temp_radiator
binary uint16size: 2
ICE box B temp (radiator)
26icu_power_supply_temp
binary uint16size: 2
ICU power supply temp
27fde_power_supply_temp_1
binary uint16size: 2
FDE power supply temp 1
28fde_power_supply_temp_2
binary uint16size: 2
FDE power supply temp 2
29spe_box_temp
binary uint16size: 2
SPE box temp
30spe_power_supply_temp_1
binary uint16size: 2
SPE power supply temp 1
31spe_power_supply_temp_2
binary uint16size: 2
SPE power supply temp 2
32paw_box_temp
binary uint16size: 2
PAW box temp
33mio_base_plate_temp_1
binary uint16size: 2
MIO base plate temp 1
34mio_base_plate_temp_2
binary uint16size: 2
MIO base plate temp 2
35mio_base_plate_temp_3
binary uint16size: 2
MIO base plate temp 3
36aft_baffle_temp_1
binary uint16size: 2
aft baffle temp 1
37aft_baffle_temp_2
binary uint16size: 2
aft baffle temp 2
38side_baffle_temp
binary uint16size: 2
side baffle temp
39fps_housing_temp_1
binary uint16size: 2
FPS housing temp 1
40fps_housing_temp_2
binary uint16size: 2
FPS housing temp 2
41asu_housing_temp_1
binary uint16size: 2
ASU housing temp 1
42ope_temp
binary uint16size: 2
OPE temperature
43esu_temp_1
binary uint16size: 2
ESU temp 1
44not_used_temp_1
binary uint16size: 2
Not used

hidden: true
45not_used_temp_2
binary uint16size: 2
Not used

hidden: true
46telescope_temp
binary uint16size: 2
Telescope temp
47ice_box_a_temp_doubler
binary uint16size: 2
ICE box A temp (doubler)
48idu_temp_1
binary uint16size: 2
IDU temp 1 (slide 1 motor temperature)
49idu_temp_2
binary uint16size: 2
IDU temp 2 (slide motor 2 temperature)
50idu_temp_3
binary uint16size: 2
IDU temp 3
51interferometer_souding_temp_1
binary uint16size: 2
Interferometer housing temp 1
52interferometer_souding_temp_2
binary uint16size: 2
Interferometer housing temp 2
53interferometer_souding_temp_3
binary uint16size: 2
Interferometer housing temp 3
54fce_temp
binary uint16size: 2
FCE temp
55not_used_temp_3
binary uint16size: 2
Not used

hidden: true
56not_used_temp_4
binary uint16size: 2
Not used

hidden: true
57not_used_temp_5
binary uint16size: 2
Not used

hidden: true
58not_used_temp_6
binary uint16size: 2
Not used

hidden: true
59fcu_temp
binary uint16size: 2
FCU temp
60fca_radiator_temp
binary uint16size: 2
FCA_radiator_temp
61olb_box_a_temp
binary uint16size: 2
OLB box A temp
62old_box_b_temp
binary uint16size: 2
OLB box B temp (not active laser box must be monitored for maintaining a minimum temperature)
63mio_if_bracket_temp_1
binary uint16size: 2
MIO I/F bracket temp 1
64mio_if_bracket_temp_2
binary uint16size: 2
MIO I/F bracket temp 2
65mio_if_bracket_temp_3
binary uint16size: 2
MIO I/F bracket temp 3
66mio_radiator_temp
binary uint16size: 2
MIO radiator temperature
67mpd_temp
binary uint16size: 2
MPD temp
68ice_box_b_temp_doubler
binary uint16size: 2
ICE box B temp (doubler)
69dbu_temp
binary uint16size: 2
DBU temp
70voltage_channels
binary array[28]size: 56
The current baseline assumes none of these values are used, hence no detailed formats are provided here.
binary uint16size: 2
71cbb_hk_parameters
binary array[11]size: 22
Temperature and Voltage information from the CBB.
binary uint16size: 2
72cbb_prt_readout_1
binary uint16size: 2
Temperature readout from CBB base #1
73cbb_prt_readout_2
binary uint16size: 2
Temperature readout from CBB base #2
74end_identifier_2
binary uint16size: 2
Constant value (FFFF, hex).
75spe_mode
binary uint16size: 2
SPE Mode (transmission rate)
76spe_clck
binary uint32size: 4
SPE Clock Cycles per IGM
77last_comm_sait_id
binary uint16size: 2
Last commanded SAIT ID (high byte: elevation; low byte: azimuth)
78last_comm_no_sweeps
binary uint16size: 2
Last commanded number of sweeps
79comm_low_fringe_count
binary uint32size: 4
Commanded Low Fringe Count
80comm_high_fringe_count
binary uint32size: 4
Commanded High Fringe Count
81comm_speed_rev_offs_cw
binary uint16size: 2
Commanded Speed Reversal Offset (sr to cw)
82comm_speed_rev_offs_ccw
binary uint16size: 2
Commanded Speed Reversal Offset (sr to ccw)
83comm_static_pos_slide_1
binary uint16size: 2
Commanded Static Position Slide #1
84comm_static_pos_slide_2
binary uint16size: 2
Commanded Static Position Slide #2
85comm_cross_over_pos
binary uint16size: 2
Commanded cross-over position
86last_comm_el_start_angle
binary uint32 (double)size: 4
Last commanded elevation start angle

unit: "1e-5 degrees"

converted unit: "degrees" (multiply by 1/100000)
87last_comm_az_start_angle
binary uint32 (double)size: 4
Last commanded azimuth start angle

unit: "1e-5 degrees"

converted unit: "degrees" (multiply by 1/100000)
88obt_start_last_scan_seq
binary uint32size: 4
OBT at start of last scan sequence

unit: "1/256 s"
89cbb_prt_readout_3
binary uint16size: 2
Temperature readout from CBB base #3
90cbb_prt_readout_4
binary uint16size: 2
Temperature readout from CBB base #4
91cbb_prt_readout_5
binary uint16size: 2
Temperature readout from CBB base #5
92cbb_cal_param_high_res
binary array[5]size: 10
CBB Calibration parameters (high resistance)
binary uint16size: 2
93cbb_cal_param_low_res
binary array[5]size: 10
CBB Calibration parameters (low resistance)
binary uint16size: 2
94rem_thermistor_channels
binary array[14]size: 28
Remaining thermistor channels
binary uint16size: 2
95rem_voltage_channels
binary array[8]size: 16
Remaining Voltage channels
binary uint16size: 2
96rem_lowlevel_voltage_channels
binary array[7]size: 14
Remaining low-level voltage channels
binary uint16size: 2
97spe_status
binary array[41]size: 82
SPE Status
binary uint16size: 2
98comm_redun_config
binary array[5]size: 10
Commanded redundancy configuration
binary uint16size: 2
99paw_comm_gain_bias_tables
binary array[17]size: 34
PAW Commanded Gain and Bias Tables
binary uint16size: 2
100spe_chan_delays
binary array[4]size: 8
SPE Channel Delays
binary uint16size: 2
101spe_band_mapping
binary array[3]size: 6
SPE Band Mapping
binary uint16size: 2
102spe_band_filter_sets
binary array[2]size: 4
SPE Band Filter Sets
binary uint16size: 2
103spe_decim_factors
binary array[7]size: 14
SPE Decimation Factors
binary uint16size: 2
104spe_timeout
binary array[3]size: 6
SPE Timeout
binary uint16size: 2
105asu_self_test_res
binary array[2]size: 4
ASU Self Test results
binary uint16size: 2
106esu_self_test_res
binary array[2]size: 4
ESU Self Test results
binary uint16size: 2
107fca_status_and_monitoring
binary array[57]size: 114
FCA Status and Monitoring
binary uint16size: 2
108prev_scan_gate_start_time
binary uint32size: 4
Previous Scan Gate Start Time
109ice_instr_mode_act
binary uint16size: 2
ICE Instrument Mode / Activity
110not_used_1
binary uint16size: 2
Not Used

hidden: true
111idx_el_start_angle_corr
binary uint16size: 2
Index for elevation start angle correction table
112idx_az_start_angle_corr
binary uint16size: 2
Index for azimuth start angle correction table
113not_used_2
binary array[5]size: 10
Not Used
binary uint16size: 2

hidden: true
114asu_esu_pos_data
binary array[257]size: 514
Measured ASU/ESU Position Data
binary uint16size: 2
115spe_operating_mode
binary uint16size: 2
SPE operating mode
116timeout_settings
binary array[3]size: 6
Timeout settings
binary uint16size: 2
117filter_set_ident
binary uint16size: 2
Filter Set Identifiers
118filter_template_identifiers
binary uint32size: 4
Filter Template Identifiers
119band_mapping_config
binary array[3]size: 6
Band Mapping Configuration
binary uint16size: 2
120channel_delay_settings
binary array[8]size: 16
Channel Delay Settings
binary uint16size: 2
121num_sampl_igm
binary uint32size: 4
Number of samples in IGM
122volt_monitor
binary array[9]size: 18
Voltage Monitor
binary uint16size: 2
123asp_temp_mon
binary array[4]size: 8
ASP Temperature Monitor
binary uint16size: 2
124chan_stat
binary array[16]size: 32
Channel Statistics
binary int16size: 2
125dsp_control_register_status
binary array[4]size: 8
DSP Control Register Status
binary uint16size: 2
126dsp_status_register_status
binary array[4]size: 8
DSP Status Register Status
binary uint16size: 2
127dec_factors
binary array[8]size: 16
Decimation Factors
binary uint16size: 2
128act_op_config_reg_stat
binary array[17]size: 34
Active OP Config Register Status
binary uint16size: 2
129self_test_conf
binary array[6]size: 12
Self Test Configuration
binary uint16size: 2
130sbit_edac_stats
binary uint16size: 2
Single-bit EDAC Statistics
131last_sbit_edac_fault_addr
binary uint16size: 2
Last single-bit EDAC fault address
132asp_latchup_err_flags
binary uint16size: 2
ASP latch-up error flags
133warn_flags
binary uint16size: 2
Warning Flags
134err_flags
binary uint16size: 2
Error Flags
135not_used_3
binary array[7]size: 14
Values nominally set to zero in format.
binary uint16size: 2

hidden: true